{{ state.meta.isTrade ? 'Sign in or register to build customer quotes you can reuse.' : 'Sign in or create an account to save items for later.' }}
This {{ state.meta.labelSingular.toLowerCase() }} is empty.
Browse the site and click "{{ state.meta.labelAdd }}" on any part.

Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
The factory plastic clutch fork pivot pins (and even some aftermarket bronze/brass ones) are known to squeak, wear excessively and even break over time and when used with high-pressure performance clutches. Our CNC-machined 303-grade stainless steel clutch fork pivot pins solves this issue, as a fit and forget part with our lifetime warranty. Fits manual transmissions only. FF5-470 vs. Plastic BMW OEM Clutch Pivot PinPowerflex Stainless Steel Clutch Pin vs. worn-out factory Clutch Pivot Pin
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Tuneable engine mounts to suit your driving demands. This mount uses a combination of our Red 65A and Purple 80A materials and can be stiffened further using the Black 95A pins. It fits 6-cyl models only except the E46 Xi and Convertible models, and for the E9* it fits the M3 only. It will not fit any 4-cyl petrol models. An increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted. We do not recommend fitting these mounts to diesel-engined vehicles due to excessive NVH. The graph above shows Load vs Displacement, peaking at 5mm displacement. PFF5-4650 is just under 200% stiffer than OE at 5mm compression, increasing to 300% with the 4 adjuster pins installed.
Black Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Tuneable engine mounts to suit your driving demands. This mount uses our Black 95A material and can be stiffened further using the Black 95A pins. It fits 6-cyl models only except the E46 Xi and Convertible models, and for the E9* it fits the M3 only. It will not fit any 4-cyl petrol models. An increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted. We do not recommend fitting these mounts to diesel-engined vehicles due to excessive NVH. The graph above shows Load vs Displacement, peaking at 5mm displacement. PFF5-4650BLK is nearly 700% stiffer than OE at 5mm compression.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit models where the Anti Roll Bar joins lower arm, not the shock absorber. This part will not fit the E36 M3 and Z3M models as a consequence.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit models where the Anti Roll Bar joins lower arm not the shock absorber.This part will not fit the E36 M3 and Z3M models as a consequence.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit models where the Anti Roll Bar joins lower arm, not the shock absorber. This part will not fit the E36 M3 and Z3M models as a consequence.
23mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering.
23mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering.
23mm
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering.
24mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering
24mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering
25mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering.
25mm
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Check anti roll bar diameter before ordering.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Use PFF5-303 for the M3, or if increased caster is required.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Use PFF5-303 for the M3, or if increased caster is required.
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Use PFF5-303 for the M3, or if increased caster is required.
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFF5-303 has an eccentric offset bore, increasing caster by 6.5mm / 0.5deg, for better turn-in response and in-corner camber gain. For M3 (not Evo) or for non-M models.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-303 has an eccentric offset bore, increasing caster by 6.5mm / 0.5deg, for better turn-in response and in-corner camber gain. For M3 (not Evo) or for non-M models.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-303 has an eccentric offset bore, increasing caster by 6.5mm / 0.5deg, for better turn-in response and in-corner camber gain. For M3 (not Evo) or for non-M models.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-3601BLK Front Wishbone Rear Bush (E46 Hybrid) is a two-piece hybrid design bush for free-rotation made using our Black 95A durometer material inner and outer bush, that combines the inner hexagonal profile of the E46 aluminium wishbone and the outer dimensions of the E30/E36 'Lollipop' mounting brackets.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-3603BLK Front Wishbone Rear Bush (E46 Hybrid, Aluminium Outer) is a two-piece hybrid design bush for free-rotation made using our Black 95A durometer material inner bush, that combines the inner hexagonal profile of the E46 aluminium wishbone and the outer dimensions of the E30/E36 'Lollipop' mounting brackets. PFF5-3603BLK uses a CNC-machined Aluminium outer shell to increase stiffness and durability further for the most demanding high-stress conditions.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-5301 includes a CNC-machined aluminium outer shell with a concentric bore for standard geometry alignment, and with the machined shell and reducing the amount of polyurethane material used, we have increased stiffness by a further 50% over PFF5-301 and PFF5-303, and a massive 250% over the standard OE rubber bush. The results are incredible, with minimal deflection under steering load and braking, whilst maintaining a balance of compliance and performance.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-5301 includes a CNC-machined aluminium outer shell with a concentric bore for standard geometry alignment, and with the machined shell and reducing the amount of polyurethane material used, we have increased stiffness by a further 50% over PFF5-301 and PFF5-303, and a massive 250% over the standard OE rubber bush. The results are incredible, with minimal deflection under steering load and braking, whilst maintaining a balance of compliance and performance.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-5303 includes a CNC-machined aluminium outer shell with an eccentric offset bore, increasing caster by 6.5mm / 0.5deg, for better turn-in response and in-corner camber gain. By including the shell and reducing the amount of polyurethane material used, we have increased stiffness by a further 50% over PFF5-301 and PFF5-303, and a massive 250% over the standard OE rubber bush. The results are incredible, with minimal deflection under steering load and braking, whilst maintaining a balance of compliance and performance.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-5303 includes a CNC-machined aluminium outer shell with an eccentric offset bore, increasing caster by 6.5mm / 0.5deg, for better turn-in response and in-corner camber gain. By including the shell and reducing the amount of polyurethane material used, we have increased stiffness by a further 50% over PFF5-301 and PFF5-303, and a massive 250% over the standard OE rubber bush. The results are incredible, with minimal deflection under steering load and braking, whilst maintaining a balance of compliance and performance.
22mm x 17mm x 26mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Depending on vehicle application, this part can be 1 or 2 per car. Size 22mm W x 17mm H x 26mm L.
22mm x 17mm x 26mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Depending on vehicle application, this part can be 1 or 2 per car. Size 22mm W x 17mm H x 26mm L.
22mm x 17mm x 26mm
Heritage Series
Out of Stock
Contact for ETA
1 Required Per Vehicle
Depending on vehicle application, this part can be 1 or 2 per car. Size 22mm W x 17mm H x 26mm L.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Made in our Red 65A durometer material, the offset bushes move the bottom of the radiator forward by 8mm to add needed clearance for the expansion tank/pulley on larger core radiators and to prevent it from touching and causing a potentially catastrophic engine failure, especially if the engine mounts are worn. They can also be fitted without draining down the coolant system and removing the radiator, making them an easy swap out.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Made in our Grey 65A durometer material, the offset bushes move the bottom of the radiator forward by 8mm to add needed clearance for the expansion tank/pulley on larger core radiators and to prevent it from touching and causing a potentially catastrophic engine failure, especially if the engine mounts are worn. They can also be fitted without draining down the coolant system and removing the radiator, making them an easy swap out.
Road Series
Out of Stock
Contact for ETA
1 Required Per Vehicle
Available singularly to suit a specific vehicle or as a handy 4-piece workshop kit, our new PowerAlign Wheel Mounting Guide Pins are designed to allow the safer mounting and easy alignment of heavy alloy wheels on most common cars to use lug bolts. The individual pins come supplied in a reusable twist tube and the 4-piece workshop kit is supplied with a steel storage case for pride of place in your toolbox. Simply thread the appropriate pin size into one of the bolt holes on the wheel hub. The wheel can then be lifted and placed on the guide pin, and easily slid into place on the hub; keeping the bolt holes aligned for other bolts to be inserted and tightened. This reduces the awkward and back-straining process of holding the wheel in place with one hand whilst lining up and threading in the first bolt; thus, reducing the risk, hassle, and strain of mounting wheels.Proven using simulated and real-world testing, the new mounting pins use high-strength CNC-machined AISI 303 Stainless Steel, some 50% stronger than plated mild steel, to ensure durability and resilience in a workshop environment, and are supplied with colour-coded 3D-printed protective sleeves for ease of identification and anodised 2011-T6 aluminium caps to absorb knocks and prevent damage to the wheel, unlike others on the market. Please click here to view all sizes available and for a wider-reaching application list in the form of a new user-friendly drop-down search function.
14mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Suitable for both 14mm and 14.5mm bars
14mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Suitable for both 14mm and 14.5mm bars
14mm
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Suitable for both 14mm and 14.5mm bars
16mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check the anti-roll bar diameter before ordering.
16mm
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check the anti-roll bar diameter before ordering.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
It will not fit E24 6 series models built before 05/1982.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
It will not fit E24 6 series models built before 05/1982.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
It will not fit E24 6 series models built before 05/1982.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
It will not fit E24 6 series models built before 05/1982.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
It will not fit E24 6 series models built before 05/1982.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
It will not fit E24 6 series models built before 05/1982.
10mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Suits cars with a standard and aftermarket rear shock absorber with a 10mm pin. Will not fit E36 and E46 Cabriolet models The above list is meant as a guide only.If your shock absorber brand is not listed, measuring the OD of the shaft will determine whether PFR5-5630-10 or PFR5-5630-12 should be fitted.
10mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Suits cars with a standard and aftermarket rear shock absorber with a 10mm pin. Will not fit E36 and E46 Cabriolet models The above list is meant as a guide only. If your shock absorber brand is not listed, measuring the OD of the shaft will determine whether PFR5-5630-10 or PFR5-5630-12 should be fitted.
12mm
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Suits cars with aftermarket rear shock absorber with a 12mm pin. Will not fit E36 and E46 Cabriolet models. The above list is meant as a guide only. If your shock absorber brand is not listed, measuring the OD of the shaft will determine whether PFR5-5630-10 or PFR5-5630-12 should be fitted.
12mm
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Suits cars with aftermarket rear shock absorber with a 12mm pin. Will not fit E36 and E46 Cabriolet models. The above list is meant as a guide only. If your shock absorber brand is not listed, measuring the OD of the shaft will determine whether PFR5-5630-10 or PFR5-5630-12 should be fitted.
12mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Suits cars with aftermarket rear shock absorber with a 12mm pin. Will not fit E36 and E46 Cabriolet models. The above list is meant as a guide only. If your shock absorber brand is not listed, measuring the OD of the shaft will determine whether PFR5-5630-10 or PFR5-5630-12 should be fitted.
Road Series
Out of Stock
Contact for ETA
4 Required Per Vehicle
On car adjustable bush offering camber and toe adjustment. Gives +/-1 degree of adjustment.
Black Series
Out of Stock
Contact for ETA
4 Required Per Vehicle
On car adjustable bush offering camber and toe adjustment. Gives +/-1 degree of adjustment.
Heritage Series
Out of Stock
Contact for ETA
4 Required Per Vehicle
On car adjustable bush offering camber and toe adjustment. Gives +/-1 degree of adjustment.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Replaces the soft OE rubber bush that sits at the end of the gear shifter arm on manual transmission equipped vehicles, a part often overlooked when upgrading transmission components. Made in our Yellow 70A durometer material and supplied with a plated steel casing, this new part is designed to eliminate slack in the gear shift and restore precision when changing gear, reinvigorating older cars and restoring the connection between the driver and their driving machine.Pairs brilliantly with PFF5-4630 or PFF5-4631 Gear Shift Arm Front Bush
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Replaces the soft OE rubber bush that sits at the end of the gear shifter arm on manual transmission equipped vehicles, a part often overlooked when upgrading transmission components. Made in our Black 95A durometer material and supplied with a plated steel casing, this new part is designed to eliminate all slack in the gear shift and restore precision when changing gear, ensuring the driver has precise control over every gear change.Pairs brilliantly with PFF5-4630 or PFF5-4631 Gear Shift Arm Front Bush
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Made from our Yellow 70A material and designed for fast road use, PFF5-4655 replaces the tear-prone factory soft-rubber transmission mounts - a common cause of knocking, misshifting, and over-revving. Fits RWD vehicles only. An increase in NVH may be felt when fitting this part. Made using CNC machined Aluminium Caps with captive securing bolts and a Yellow 70A Durometer polyurethane body, they increase stiffness over OE by 150%, whilst minimising NVH transmission.They are also the perfect accompaniment to our PFF5-4650 Tuneable Engine Mount on E36/E46/E9* models.
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Made from our Grey 70A material and designed for fast road use, PFF5-4655H replaces the tear-prone factory soft-rubber transmission mounts - a common cause of knocking, misshifting, and over-revving. Fits RWD vehicles only. An increase in NVH may be felt when fitting this part. Made using CNC machined Aluminium Caps with captive securing bolts and a Yellow 70A Durometer polyurethane body, they increase stiffness over OE by 150%, whilst minimising NVH transmission.They are also the perfect accompaniment to our PFF5-4650 Tuneable Engine Mount on E36/E46/E9* models.
Black Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Made in our Black 95A material and designed for motorsport use, PFF5-4655BLK replaces the tear-prone factory soft-rubber transmission mounts - a common cause of knocking, misshifting, and over-revving. Fits RWD vehicles only. An increase in NVH may be felt when fitting this part. Made using CNC machined Aluminium Caps with captive securing bolts and a Black 95A Durometer polyurethane body, they increase stiffness over OE by 375% for complete control over powertrain movement.They are also the perfect accompaniment to our PFF5-4650 Tuneable Engine Mount on E36/E46/E9* models.
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Made from our Purple 80A material and designed for tuned vehicles and track days, PFF5-4655P replaces the tear-prone factory soft-rubber transmission mounts - a common cause of knocking, misshifting, and over-revving. Fits RWD vehicles only. An increase in NVH may be felt when fitting this part. Made using CNC machined Aluminium Caps with captive securing bolts and a Purple 80A Durometer polyurethane body, they increase stiffness over OE by 260% for razor-sharp engine response.They are also the perfect accompaniment to our PFF5-4650 Tuneable Engine Mount on E36/E46/E9* models.