{{ state.meta.isTrade ? 'Sign in or register to build customer quotes you can reuse.' : 'Sign in or create an account to save items for later.' }}
This {{ state.meta.labelSingular.toLowerCase() }} is empty.
Browse the site and click "{{ state.meta.labelAdd }}" on any part.

19mm
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
For pre-2010 Vehicles with 3/4" bolts PFR32-110 is made using our most rigid Black 95A material to replicate the stiffness of the original rubber part in our non-perishable material. This specially designed part is shaped to allow a controlled amount of articulation as the A frame moves through its travel.A short video to help as a guide to remove bushes such as these can be found by clicking here.
19mm
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
For pre-2010 Vehicles with 3/4" bolts PFR32-110 is made using our most rigid Black 95A material to replicate the stiffness of the original rubber part in our non-perishable material. This specially designed part is shaped to allow a controlled amount of articulation as the A frame moves through its travel.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit front or rear positions of the anti roll bar link.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit front or rear positions of the anti roll bar link.
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
This part is designed to fit front or rear positions of the anti roll bar link.
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
This part is designed to fit front or rear positions of the anti roll bar link.
Road Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
Please check the number required for your vehicle prior to ordering.
25mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check anti roll bar diameter before ordering.
25mm
Heritage Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Please check anti roll bar diameter before ordering.
25mm
Heritage Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Please check anti roll bar diameter before ordering.
28mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles with aftermarket anti roll bars measuring 28mm diameter. Please check anti roll bar diameter before ordering.
28mm
Heritage Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
This part fits vehicles with aftermarket anti roll bars measuring 28mm diameter. Please check anti roll bar diameter before ordering.
80mm Tall
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with raised suspension. For standard and lowered versions please use PF32-130-60 and PF32-130-40 respectively.
80mm Tall
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with raised suspension. For standard and lowered versions please use PF32-130-60 and PF32-130-40 respectively.
80mm Tall
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with raised suspension. For standard and lowered versions please use PF32-130-60 and PF32-130-40 respectively.
40mm Tall
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with lowered suspension. For standard height and extended versions, please use PF32-130-60 and PF32-130-80 respectively.
40mm Tall
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with lowered suspension. For standard height and extended versions, please use PF32-130-60 and PF32-130-80 respectively.
40mm Tall
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with lowered suspension. For standard height and extended versions, please use PF32-130-60 and PF32-130-80 respectively.
60mm Tall
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with standard height suspension. For extended versions for raised vehicles, please use PF32-130-80 and for lowered vehicles please use PF32-130-40 respectively.
60mm Tall
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with standard height suspension. For extended versions for raised vehicles, please use PF32-130-80 and for lowered vehicles please use PF32-130-40 respectively.
60mm Tall
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with standard height suspension. For extended versions for raised vehicles, please use PF32-130-80 and for lowered vehicles please use PF32-130-40 respectively.
44mm
Road Series
In Stock
Est. despatch Same or next working day
4 Required Per Vehicle
This part suits vehicles with the wider 44mm radius arms. For vehicles with 38mm radius arms please use PFF32-107. PFF32-108 uses our Black 95A material which helps to increase the stiffness of the original parts by over 30%. It is manufactured in two halves for ease of fitting. A short video to help as a guide to remove bushes such as these can be found by clicking here.
Road Series
Out of Stock
Contact for ETA
4 Required Per Vehicle
PFF32-108G-25 has been engineered to provide caster correction for vehicles that have been lifted or lowered by 25mm. This part suits wider 44mm arms fitted on models chassis number LA onwards. Correcting the caster on your vehicle will provide:Greater stabilityImproved handling and tyre gripMore weight and detail to steering The kit includes robust CNC machined steel shells to prevent rotation and to retain the corrected geometry. PFF32-108G uses our Black 95A material which helps to increase the stiffness of the original parts by over 30%. It is manufactured in two halves for ease of fitting. A short video to help as a guide to remove bushes such as these can be found by clicking here.
Road Series
Out of Stock
Contact for ETA
4 Required Per Vehicle
PFF32-108G-50 has been engineered to provide caster correction for vehicles that have been lifted or lowered by 50mm. This part suits wider 44mm arms fitted on models chassis number LA onwards. Correcting the caster on your vehicle will provide:Greater stabilityImproved handling and tyre gripMore weight and detail to steering The kit includes robust CNC machined steel shells to prevent rotation and to retain the corrected geometry. PFF32-108G uses our Black 95A material which helps to increase the stiffness of the original parts by over 30%. It is manufactured in two halves for ease of fitting. A short video to help as a guide to remove bushes such as these can be found by clicking here.
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
PFF32-109 replicates original steering geometry. Made from our Yellow 70A material, this part allows the required articulation that this bush location demands. To counter pull to the left or right, please use PFF32-109G05 for 0.5 degrees offset or PFF32-109G1 for 1 degree offset.
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFF32-109G is designed to counter pull to the left or right by correcting the steering using our offset bushes. The kit includes parts to correct steering geometry by 0.5 and 1 degrees. The kit includes replacement washers and Nyloc nuts for a clean installation and an accurate torque setting. Made from our Yellow 70A material, this part allows the required articulation that this bush location demands.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF32-109G is designed to counter pull to the left or right by correcting the steering using our offset bushes. The kit includes parts to correct steering geometry by 0.5 and 1 degrees. The kit includes replacement washers and Nyloc nuts for a clean installation and an accurate torque setting. Made from our Yellow 70A material, this part allows the required articulation that this bush location demands.
30mm OD
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles up to VIN 2A626645. For later vehicles please use PFF32-301.
30mm OD
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles up to VIN 2A626645. For later vehicles please use PFF32-301.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Included within this pack are the following parts: PFF32-101 Panhard Rod Bush 30mm PFF32-108 Front Radius Arm Front Bush PFF32-109 Front Radius Arm Rear Bush PFR32-110 A-Frame to Chassis Bush PFR32-111 Rear Radius Arm Front Bush PFR32-112 Rear Trailing Arm to Axle BushThis Handling Pack contains a selection of parts from a complete vehicle listing, click here to see more parts available.
19mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 90, 110, 120, except 90 V8 Efi & Td5. Please check anti roll bar diameter before ordering.
19mm
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 90, 110, 120, except 90 V8 Efi & Td5. Please check anti roll bar diameter before ordering.
19mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 110 and 130 models. Please check anti roll bar diameter before ordering.
19mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 90 V8 Efi & Td5. Please check anti roll bar diameter before ordering.
19mm
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 90 V8 Efi & Td5. Please check anti roll bar diameter before ordering.
28mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 110 and 130 models. Please check anti roll bar diameter before ordering.
28mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits 90 V8 Efi & Td5. Please check anti roll bar diameter before ordering.
80mm Tall
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with raised suspension. For standard and lowered versions please use PF32-130-60 and PF32-130-40 respectively.
40mm Tall
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with lowered suspension. For standard height and extended versions, please use PF32-130-60 and PF32-130-80 respectively.
60mm Tall
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part is designed to fit vehicles with standard height suspension. For extended versions for raised vehicles, please use PF32-130-80 and for lowered vehicles please use PF32-130-40 respectively.
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
During testing of the original rubber bushes, it was discovered that the resting position of the vehicle forces the bush into a stressed angle that leads to premature failure and uneven spring rate characteristics through the suspension travel. PFR32-111 has been engineered to align the radius arm with a 3.5 degrees static angle of the radius arm to allow neutral articulation for improved performance and longevity.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
During testing of the original rubber bushes, it was discovered that the resting position of the vehicle forces the bush into a stressed angle that leads to premature failure and uneven spring rate characteristics through the suspension travel. PFR32-111 has been engineered to align the radius arm with a 3.5 degrees static angle of the radius arm to allow neutral articulation for improved performance and longevity.
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFR32-133 is designed to accommodate the natural arc of the shock absorber through the use of our Yellow 70A material, that when combined with voiding will allow controlled articulation. This serves to reduce the transmission of vibration and will mean a smoother ride for your vehicle and provide you with long lasting bushes.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR32-133 is designed to accommodate the natural arc of the shock absorber through the use of our Yellow 70A material, that when combined with voiding will allow controlled articulation. This serves to reduce the transmission of vibration and will mean a smoother ride for your vehicle and provide you with long lasting bushes.
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
PFR32-112 uses our Black 95A material which helps to increase the stiffness of the original parts by 25%. It is manufactured in two halves for ease of fitting. A short video to help as a guide to remove bushes such as these can be found by clicking here.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Each carton contains 2 X bushes made up of 4 X PU parts. Early Defender models use 4 X bushes on the front and 2 X bushes at the rear. Defender models from 02 onwards use 4 X front bushes only. PF32-132 is designed to accommodate the natural arc of the shock absorber through the use of our Yellow 70A material, that when combined with voiding will allow controlled articulation. This serves to reduce the transmission of vibration and will mean a smoother ride for your vehicle and provide you with long lasting bushes.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Each carton contains 2 X bushes made up of 4 X PU parts. Early Defender models use 4 X bushes on the front and 2 X bushes at the rear. Defender models from 02 onwards use 4 X front bushes only. PF32-132 is designed to accommodate the natural arc of the shock absorber through the use of our Yellow 70A material, that when combined with voiding will allow controlled articulation. This serves to reduce the transmission of vibration and will mean a smoother ride for your vehicle and provide you with long lasting bushes.
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFR32-134 is designed to accommodate the natural arc of the shock absorber through the use of our Yellow 70A material
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This part fits the pin end of the steering damper and boosts the stiffness of the original bush by almost 300% for increased performance and longevity. For the eye end please use PFF32-135.
Heritage Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This part fits the pin end of the steering damper and boosts the stiffness of the original bush by almost 300% for increased performance and longevity. For the eye end please use PFF32-135.