{{ state.meta.isTrade ? 'Sign in or register to build customer quotes you can reuse.' : 'Sign in or create an account to save items for later.' }}
This {{ state.meta.labelSingular.toLowerCase() }} is empty.
Browse the site and click "{{ state.meta.labelAdd }}" on any part.

Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
The factory plastic clutch fork pivot pins (and even some aftermarket bronze/brass ones) are known to squeak, wear excessively and even break over time and when used with high-pressure performance clutches. Our CNC-machined 303-grade stainless steel clutch fork pivot pins solve this issue, as a fit-and-forget part with our lifetime warranty. Fits manual gearboxes only. PFF5-170 vs. worn-out plastic factory clutch pivot pin.
16mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check anti roll bar diameter before ordering
16mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check anti roll bar diameter before ordering
22.5mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check anti roll bar diameter before ordering
22.5mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check anti roll bar diameter before ordering
24mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Please check anti roll bar diameter before ordering
24mm
Black Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
Please check anti roll bar diameter before ordering
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFF5K-101 Front Wishbone Rear Bush & Bracket fits Mini Gen 1 R50/R53 and uses our existing PFF5-101 bush. A lasting, better-performing polyurethane bush alternative, like Powerflex, has always been a popular upgrade for owners but whilst our bushes are very easy to fit, sometimes removing the original bushes from the OE housing brackets can be difficult, especially for those with limited access to pressing or pulling tools. Pre-installed in quality brackets, they simply require fitting onto the arm and bolting into position saving both time and money.
Black Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
PFF5K-101 Front Wishbone Rear Bush & Bracket fits Mini Gen 1 R50/R53 and uses our existing PFF5-101 bush. A lasting, better-performing polyurethane bush alternative, like Powerflex, has always been a popular upgrade for owners, but whilst our bushes are very easy to fit, sometimes removing the original bushes from the OE housing brackets can be difficult, especially for those with limited access to pressing or pulling tools. Pre-installed in quality brackets, they simply require fitting onto the arm and bolting into position, saving both time and money.
Black Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
PFF5K-101 Front Wishbone Rear Bush & Bracket fits Mini Gen 1 R50/R53 and uses our existing PFF5-101 bush. A lasting, better-performing polyurethane bush alternative, like Powerflex, has always been a popular upgrade for owners, but whilst our bushes are very easy to fit, sometimes removing the original bushes from the OE housing brackets can be difficult, especially for those with limited access to pressing or pulling tools. Pre-installed in quality brackets, they simply require fitting onto the arm and bolting into position, saving both time and money.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-101G offers an additional +2 of caster and is a high-performance option to PFF5-101 for people wanting the very best from their Mini. This new part, fitted to the rear of the front wishbone has a hard anodised aluminium outer shell with one of our unique low-friction polyurethane centre bushes. The poly/alu combination creates a low friction rotating bush reducing the forces acting on the arm. Lower arm deflection has been decreased by reducing the compliant material within the aluminium shell. Additional caster angle will give more negative camber when cornering giving improved tyre to road contact. Results are greater precision and optimised geometry when turning, improving grip, steering control and feel with less movement in the arm under cornering and braking.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-101GBLK offers an additional +2 of caster and is a high-performance option to PFF5-101 for people wanting the very best from their Mini. This new part, fitted to the rear of the front wishbone has a hard anodised aluminium outer shell with one of our unique low-friction polyurethane centre bushes. The poly/alu combination creates a low friction rotating bush reducing the forces acting on the arm. Lower arm deflection has been decreased by reducing the compliant material within the aluminium shell. Additional caster angle will give more negative camber when cornering giving improved tyre to road contact. Results are greater precision and optimised geometry when turning, improving grip, steering control and feel with less movement in the arm under cornering and braking.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
For petrol R50/R52 One 1.4/1.6 models only
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
For petrol R50/R52 One 1.4/1.6 models only
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Fits Mini Gen 1 Cooper S & JCW only
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Fits Mini Gen 1 Cooper S & JCW only
80mm Diameter
Road Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
PF5-4660 is a polyurethane jack pad to fit into the plastic lifting points found on most modern BMW and related vehicles and is designed to help lift stability and location, whilst protecting the underside of your vehicle. Fits the following vehicles: BMW 1 Series E81, E87, E88 (2004 - 2013) BMW 1 M E82 (2010 - 2012) BMW 1 Series F20, F21 (2011 - 2019) BMW 1 Series F40 (2018 on) BMW 1 Series F52 (2017 on) BMW 2 Series F22, F23 (2013 - 2020) BMW 2 Series Gran Coupe F44 (2019 on) BMW 2 Series Active Tourer F45, F46 (2014 - 2019) BMW M2 F87 (2015 on) BMW 3 Series E46 (1999 - 2006) BMW 3 Series E90, E91, E92, E93 (2005 - 2013) BMW 3 Series F30, F31, F34 (2011 - 2018) BMW M3 F80 (2011 - 2018) BMW 3 Series G20, G21, G28 (2018 on) BMW M3 G80 (2018 on) BMW 4 Series F32, F33, F36 (2013 - 2021) BMW M4 F82, F83 (2013 - 2021) BMW 4 Series G22, G23 (2020 on) BMW M4 G82, G83 (2020 on) BMW 5 Series E39 (1996 - 2004) BMW 5 Series E60, E61 (2003 - 2010) BMW 5 Series Gran Turismo F07 (2009 - 2016) BMW 5 Series F10, F11 (2010 - 2016) BMW 5 Series G30, G31 (2016 on) BMW M5 F90 (2017 on) BMW 6 Series E63, E64 (2003 - 2010) BMW 6 Series F06, F12, F13 (2011 - 2018) BMW 6 Series Gran Turismo G32 (2017 on) BMW 7 Series E38 (1994 - 2002) BMW 7 Series E65, E66, E67 (2001 - 2008) BMW 7 Series F01, F02, F03, F04 (2007 - 2016) BMW 7 Series G11, G12 (2015 on) BMW M8 F91, F92, F93 (2019 on) BMW 8 Series G14, G15, G16 (2018 on) BMW X1 E84 (2008 - 2015) BMW X1 F48 (2016 on) BMW X2 F39 (2017 on) BMW X3 E83 (2003 - 2010) BMW X3 F25 (2009 - 2017) BMW X3 F97, G01 (2017 on) BMW iX3 G08 (2020 on) BMW X4 F26 (2013 - 2018) BMW X4 F98, G02 (2018 on) BMW X5 E53 (1999 - 2006) BMW X5 E70 (2006 - 2013) BMW X5 F15, F85 (2013 - 2019)BMW X5 F85 M (2013 - 1018) BMW X5 F95, G05 (2018 on) BMW X6 E71, E72 (2007 - 2014) BMW X6 F16, F86 (2015 - 2019) BMW X6 F96, G06 (2019 on) BMW X7 G07 (2018 on) BMW Z4 E85, E86 (2003 - 2009) BMW Z4 E89 (2009 - 2018) BMW Z4 G29 (2018 on) Mini Hatch R50, R53 (2000 - 2006) Mini Hatch R56 (2006 - 2013) Mini Hatch F55, F56 (2014 - 2024) Mini Cabriolet R52 (2004 - 2008) Mini Cabriolet R57 (2009 - 2015) Mini Cabriolet F57 (2014 - 2024) Mini Clubman R55 (2007 - 2014) Mini Clubman F54 (2015 - 2024) Mini Countryman F60 (2017 - 2024) Mini Coupe R58 (2011 - 2015) Mini Roadster R59 (2012 - 2015) Rolls-Royce Ghost RR4 (2008 - 2018) Rolls-Royce Phantom RR1 (2003 - 2017) Rolls-Royce Phantom RR11, RR12 (2017 on) Rolls-Royce Wraith RR5 (2012 - 2018) Rolls-Royce Dawn RR6 (2015 - 2018) Rolls-Royce Cullinan RR31 (2017 on) Toyota Supra MK5 J29 (2019 on)
Road Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
This bush is an insert and fits into the original bush.
Road Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
This bush is an insert and fits into the original bush.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This bush is an insert and fits into the original bush in bracket.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This replaces the complete original bush in bracket, if you would like to fit an insert only then please use PFF5-107. The bush comes with an insert giving the option to stiffen the mount up by fitting the insert into the voids enabling you to change the bush to suit your driving style.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This replaces the complete original bush in bracket, if you would like to fit an insert only then please use PFF5-107. The bush comes with an insert giving the option to stiffen the mount up by fitting the insert into the voids enabling you to change the bush to suit your driving style.
Road Series
Out of Stock
Contact for ETA
1 Required Per Vehicle
An anodised CNC-Machined 6082 Aluminium mount pre-fitted with polyurethane bushes, for a true bolt-off, bolt-on replacement, with no pressing or assembly required. This Road Series mount provides a 100% increase in overall stiffness over the original voided mount, using a combined Purple 80A durometer small bush; and a 2-piece design large bush with Purple 80A and Yellow 70A bush components. With a minimal increase in NVH, reduced wheel hop and a more direct transition of power to the road, it is suitable for standard and mildly tuned vehicles and would be considered as the next step upgrade to our PFF5-107 and PFF5-120 offerings. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine and chassis. The harder the material used, the greater the NVH transmitted.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
An anodised CNC-Machined 6082 Aluminium mount pre-fitted with polyurethane bushes, for a true bolt-off, bolt-on replacement, with no pressing or assembly required. This Fast Road mount combines our stiffer Purple 80A and Black 95A materials for the larger bush, providing a 200% increase in stiffness over OE for even sharper response and durability for more extensively tuned vehicles or mild track use. With a minimal increase in NVH, reduced wheel hop and a more direct transition of power to the road, it is suitable for standard and mildly tuned vehicles and would be considered as the next step upgrade to our PFF5-107 and PFF5-120 offerings. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine and chassis. The harder the material used, the greater the NVH transmitted.
Black Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
An anodised CNC-Machined 6082 Aluminium mount pre-fitted with polyurethane bushes, for a true bolt-off, bolt-on replacement, with no pressing or assembly required. This Black Series mount uses our Black 95A material for all bush components to maximise mount stiffness, resulting in a mega 430% increase over the stock mount for uncompromising powertrain control for serious track and motorsports use. With a minimal increase in NVH, reduced wheel hop and a more direct transition of power to the road, it is suitable for standard and mildly tuned vehicles and would be considered as the next step upgrade to our PFF5-107 and PFF5-120 offerings. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine and chassis. The harder the material used, the greater the NVH transmitted.
Black Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
An anodised CNC-Machined 6082 Aluminium mount pre-fitted with polyurethane bushes, for a true bolt-off, bolt-on replacement, with no pressing or assembly required. This Black Series mount uses our Black 95A material for all bush components to maximise mount stiffness, resulting in a mega 430% increase over the stock mount for uncompromising powertrain control for serious track and motorsports use. With a minimal increase in NVH, reduced wheel hop and a more direct transition of power to the road, it is suitable for standard and mildly tuned vehicles and would be considered as the next step upgrade to our PFF5-107 and PFF5-120 offerings. A small increase in NVH, usually at idle, should be expected when stiffening the connecting mount between the engine and chassis. The harder the material used, the greater the NVH transmitted.
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Additional Parts To Tighten Up The Front Wishbone Rear Bush, A Must For Track Day & Circuit Cars
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Additional Parts To Tighten Up The Front Wishbone Rear Bush, A Must For Track Day & Circuit Cars
Road Series
Out of Stock
Contact for ETA
1 Required Per Vehicle
Available singularly to suit a specific vehicle or as a handy 4-piece workshop kit, our new PowerAlign Wheel Mounting Guide Pins are designed to allow the safer mounting and easy alignment of heavy alloy wheels on most common cars to use lug bolts. The individual pins come supplied in a reusable twist tube and the 4-piece workshop kit is supplied with a steel storage case for pride of place in your toolbox. Simply thread the appropriate pin size into one of the bolt holes on the wheel hub. The wheel can then be lifted and placed on the guide pin, and easily slid into place on the hub; keeping the bolt holes aligned for other bolts to be inserted and tightened. This reduces the awkward and back-straining process of holding the wheel in place with one hand whilst lining up and threading in the first bolt; thus, reducing the risk, hassle, and strain of mounting wheels.Proven using simulated and real-world testing, the new mounting pins use high-strength CNC-machined AISI 303 Stainless Steel, some 50% stronger than plated mild steel, to ensure durability and resilience in a workshop environment, and are supplied with colour-coded 3D-printed protective sleeves for ease of identification and anodised 2011-T6 aluminium caps to absorb knocks and prevent damage to the wheel, unlike others on the market. Please click here to view all sizes available and for a wider-reaching application list in the form of a new user-friendly drop-down search function.
Road Series
Out of Stock
Contact for ETA
1 Required Per Vehicle
Only fits models 2003 to 2006. It will not fit R53 GP models due to a different rear trailing arm bush. Included within this pack are the following parts: PFF5-101 Front Wishbone Rear Bush PFF5-101MS PFF5-101 Support Kit PFF5-120 Lower Engine Mount Large Bush PFR5-1104 Rear Trailing Arm Front Bush PFR5-115 Rear Shock Top Mounting BushThis Handling Pack contains a selection of parts from a complete vehicle listing, click here to see more parts available.
16mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles with a 16mm anti roll bar diameter.
16mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles with a 16mm anti roll bar diameter.
17mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles with a 17mm diameter anti roll bar.
17mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
This part fits vehicles with a 17mm diameter anti roll bar.
60mm
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-1103 is a complete bush that fits into trailing arm bracket OE numbers: 33306799089 33306799090, 33309807099 and 3330980710. For inserts use PFR5-1102 which fit into the original rubber bush. This bush fits GEN2 models.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-1103 is a complete bush that fits into trailing arm bracket OE numbers: 33306799089 33306799090, 33309807099 and 3330980710. For inserts use PFR5-1102 which fit into the original rubber bush.
60mm
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFR5-1104 is a full replacement bush that fits later Gen1 models from 2003 on with a 60mm OD bush. For the earlier models with an 80mm OD bush, use PFR5-1105. For inserts that fit into the original bush, use PFR5-1102.
60mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-1104 is a full replacement bush that fits later Gen1 models from 2003 on with a 60mm OD bush. For the earlier models with an 80mm OD bush, use PFR5-1105. For inserts that fit into the original bush, use PFR5-1102.
80mm
Road Series
Out of Stock
Contact for ETA
2 Required Per Vehicle
PFR5-1105 is a full replacement bush that fits early Gen1 models up to 2003 with an 80mm OD bush. For later models with a 60mm OD bush, use PFR5-1104. For inserts that fit into the original bush, use PFR5-110.
80mm
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-1105 is a full replacement bush that fits early Gen1 models up to 2003 with an 80mm OD bush. For later models with a 60mm OD bush, use PFR5-1104. For inserts that fit into the original bush, use PFR5-110.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-110 inserts will fit models up to 05/2003. For a full replacement bush, please use PFR5-1105
Road Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-1102 inserts will fit models from 05/2003. For a full replacement bush please use PFR5-1104
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-1102BLK inserts will fit models from 05/2003. For a full replacement bush, please use PFR5-1104BLK
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFR5-110BLK inserts will fit models up to 05/2003. For a full replacement bush, please use PFR5-1105BLK
Road + Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
PFF5-131G is a straightforward way to change the virtual roll centre of the car to increase resistance to body roll and correct suspension geometry on lowered vehicles. Lowering the car will change the angle of the front wishbone causing suspension compression even before the suspension moves. Our roll centre adjuster kit will restore the original roll centre on these cars and includes a 5mm spacer for fine-tuning and to cater for different lowered amounts (N.B. The spacer is only suitable for 17-inch wheels and larger). Our kit includes longer High Tensile bolts to accommodate the additional thickness of the ball joint assembly. *Ball joint NOT included*. Spacer included for additional adjustment to cater for especially lowered vehicles and 17" and above wheel sizes.
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Fits either end of the belt damper on supercharged Mini Cooper S models
Road Series
In Stock
Est. despatch Same or next working day
2 Required Per Vehicle
Fits either end of the belt damper on supercharged Mini Cooper S models
Black Series
In Stock with supplier
Est. despatch 48-72 hours
2 Required Per Vehicle
Fits either end of the belt damper on supercharged Mini Cooper S models
Road Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
This kit contains 2 x PU bump stops, 2 x Rubber Gaiter and 2 x Cable ties to secure.
Road Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
This kit contains 2 x PU bump stops, 2 x Rubber Gaiter and 2 x Cable ties to secure.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
PFF5-124 is a quick and easy way to stiffen the OE oil-filled engine mount, improving throttle response and gear changes by providing greater engine stability. Some added NVH may be experienced when fitting this part. Made in our Yellow 70A material this product is for road/fast road use.
Black Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
PFF5-124BLK is a quick and easy way to stiffen the OE oil-filled engine mount, improving throttle response and gear changes by providing greater engine stability. Some added NVH may be experienced when fitting this part. Made in our hardest Black 95A material, this product is for track/motorsport use.
Black Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
PFF5-124BLK is a quick and easy way to stiffen the OE oil-filled engine mount, improving throttle response and gear changes by providing greater engine stability. Some added NVH may be experienced when fitting this part. Made in our hardest Black 95A material, this product is for track/motorsport use.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
PFF5-124R is a quick and easy way to stiffen the OE oil-filled engine mount, improving throttle response and gear changes by providing greater engine stability. Some added NVH may be experienced when fitting this part. Made in our Red 65A material, this product is for diesel vehicles.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Fits models up to 2004. Models from 2004 onwards use an oil-filled upper engine mount and don't have an upper support bracket. This bush is an insert and fits into the original bush, it does not replace the original bush.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
Fits models up to 2004. Models from 2004 onwards use an oil-filled upper engine mount and don't have an upper support bracket. This bush is an insert and fits into the original bush, it does not replace the original bush.
Road Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This replaces the complete original bush in bracket, if you would like to fit an insert only then please use PFF5-105. The bush comes with an insert giving the option to stiffen the mount up by fitting the insert into the voids enabling you to change the bush to suit your driving style.
Black Series
In Stock with supplier
Est. despatch 48-72 hours
1 Required Per Vehicle
This replaces the complete original bush in bracket, if you would like to fit an insert only then please use PFF5-105. The bush comes with an insert giving the option to stiffen the mount up by fitting the insert into the voids enabling you to change the bush to suit your driving style.
Road Series
Out of Stock
Contact for ETA
1 Required Per Vehicle
Fits models up to 2004. Models from 2004 onwards use an oil-filled upper engine mount and don't have an upper support bracket.
Black Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
Fits models up to 2004. Models from 2004 onwards use an oil-filled upper engine mount and don't have an upper support bracket.
Black Series
In Stock
Est. despatch Same or next working day
1 Required Per Vehicle
Fits models up to 2004. Models from 2004 onwards use an oil-filled upper engine mount and don't have an upper support bracket.